Hydraulic Actuator

Hydraulic Actuator is a mechanical device that is used for controlling a mechanism for fluid liquid power to do in a simple work. The fluid is then filtered and re-pumped. The path taken by hydraulic fluid is called a hydraulic circuit of which there are several types for the hydraulic fluid to do work, it must flow to the actuator and or motors, then return to its reserver. Mechanical Actuators operate by conversion of rotary motion into linear motion while the Hydraulics is used for the generation, control, and transmission of power by the use of pressurized liquids.Now in our website http://www.magemarinestore.com/ you can replace the Hydraulic Actuator of your jack plate and tilt trim unit.You can also order other boat parts by visiting our website and check our products that you will need in your boat,just visit our website and search the name of the product that your looking for.

CMC Hydraulic Actuator 7050

A gauge is a helpful device use in measuring or testing instrument.  Typically we can find it in a boat, car or any type of vehicles. It is use to determine the height of the motor without looking back, allowing the driver to maintain a forward view at all times. When use it in a boat, the gauge indicates the presence or the quantity level of water in the sea.  The measurement of water level is really important. It can help you identify what speed to maintain for your safety.

 There are several kind of gauges to buy.  In fact MagemarineStore sells different gauges for your boat. We have this gauge kit 6077 for CMC jack plates. Another one is the conversion gauge kit 51207 for CMC PT-130 tilt trim units use only not for PT-35 units. Its sending unit is totally fastened and water resistant, which removes any moisture problems. The up down toggle switch of this gauge is standard equipment. To have a sealed, drip proof and mounted in the dash boat, you must have this water pressure gauge 20320. Usually the maximum engine height is determined by the hole slot and engine water pressure at top end speed. If the engine is adjusted too high there will be loss of water pressure to the engine at top end speed/or the prop will cavitate coming out of the hole. This pressure gauge is recommended on high performance applications when the motor is raised to extreme heights. This allow for constant monitoring of the cooling system.

Purchase a gauge for your safety and convenience. You can visit our different gauges here: http://www.magemarinestore.com/japlandtitru.html .

We have this ignition 113-1726 for your OMC/Johnson Evinrude for only $100. This includes cover & gasket. It will fit your 1997 to 1978, 3 cylinder and 1976-1978 V6 engine applications. Note that this unit replaces part numbers: 581334, 581551, 581552, 581726, 582057 (Power Pack 3 w/cover & gasket), 18-5763and 18-5765.

Having trouble on how to install this ignition 113-1726 for your 3 cylinder OMC/Johnson Evinrude?
Read the procedure below:

1. Remove the old power pack cover.
2. Disconnect all wires from the old power pack.
3. Remove the old power pack and save the mounting bolts.
Check for DC voltage on the kill (stop) wire (usually Black/Yellow) with the key-switch in the on and off position. At no time should
you see over 2 volts DC on this wire as severe damage to the power pack can occur.
5. Install the new power pack using the original bolts.
6. Reconnect the wires according to the connection guide below (also located on the cover).
7. Install the new cover and gasket using the new screws included with the new pack.

How about for your 6 Cylinder Engine?
Here:

1. Remove the old power pack cover.
2. Disconnect all wires from the old power pack. Watch for the connections from the Timer Base to the pack.
3. Remove the old power pack and save the mounting bolts.
4. Check for DC voltage on the kill (stop) wire (usually Black/Yellow) with the key-switch in the on and off position. At no time should
you see over 2 volts DC on this wire as severe damage to the power pack can occur.
5. Install the new power pack using the original bolts.
6. Connect the stator, kill and coil wires to the new pack.
7. Connect the White Timer Base wire to the Black/White Terminal.
8. Connect the Blue Timer Base wire to the White/ Black Terminal for # 1.
9. Connect the Violet Timer Base wire to the White/ Black Terminal for # 2
10. Connect the Green Timer Base wire to the White/ Black Terminal for # 3.
11. Reconnect the wires according to the connection guide located on the cover.
12. Install the new cover and gasket using the new screws included with the new pack.

If you want to order just click this link: http://www.magemarinestore.com/omcig117.html

Anything that you need for your boat? Just one click at http://www.magemarinestore.com/ and you will discover it. Take some time to make a tour on our website and you will find this trigger 134-6454 for only $84.00. It fits 45, 50, 80 and 85 HP of mercury motor. Replaces part numbers 77000A1 & 96453A2.

Now is the time to throw your old, damaged and rotten triggers. Come visit this link: http://www.magemarinestore.com/cdimeretr131.html

Isn't time for you to replace your Chrysler/Force engine ignitions?

Replace your Chrysler/Force ignitions, battery ignitions, magneto ignition, magnapower capacitor, rectifiers, stators and triggers. Here is the link: http://www.magemarinestore.com/chigpr.html

If you need battery ignition pack 115-3301 click this link : http://www.magemarinestore.com/cdichfobaigp.html and see what replaces your motor. This fits Chrysler/Force outboard motors for only $223.00.
Note that this unit does not have a tachometer circuit input.

Would you like to get discount via USPS shipping? Email us at sales@magemarinestore.com.

Sometimes problems come unexpectedly. Do you have life problems or boat problems? To solve either love or boat problems, you can use these three questions in order to solve it: First what could I do? Second, what could I read? And third, who could I ask? MagemarineStore can help you with your boat problems, you can read information of our different boat products. You can fix your boat parts or replace it with the new one . And you can ask questions by sending an email at sales@magemarinestore.com

 Meanwhile, if you need gear assembly for your boat or ARCO products? Here is the quickest link to view information: http://www.magemarinestore.com/ardvhedureid.html.

So order now and fix your boat. Then leave all your problems by riding on it!