Mercury Stator 174-3996

Your 1970 Mercury 7.5 HP needs to replace your old stator with new stator part no. 174-3996. This stator will replace part numbers 18-5855, 336-3692, 336-3996, 336-3996A7, 339-3962A4, 339-3996A4, 339-3996A6, 339-3996A7, 9-25501. Two insular blocks with part no. 994-3981 are included. Note that the insulator blocks included with this stator is important. You are strongly advised to install them and closely inspect the point wires for cracking or racing. This system operates at a much higher voltage than the normal systems and what would be acceptable on other systems will cause problems.

For technical information do not start and run engine on a flushing attachment or ear muffs and active the kill circuit.  

Visit MagemarineStore to order this item.

We also sell part no. 3420 aside from part no. 3412 of ARCO products.  Another outboard starter replacement for your 2 stroke Yamaha that should be 25 to 40 HP. Two stroke Mariner of 20 to 40 HP and Hitachi S108-80, S108-80A, S108-80B. It has 11-tooth drive gear.  The price is very affordable compare to others. You can use our very useful website to order part no. 3420 online: http://www.magemarinestore.com/ar34oust2.html. If you are looking for the correct part for your motor the application guide is made for you http://www.magemarine.com/arco/  or you can just email us the serial#, model#, how much HP and type of your motor at sales@magemarinestore.com.

A failure directly caused by rust, corrosion or submersion is not covered by warranty.

ARCO treats every component with special rust and corrosion resistant coatings to prevent water damage. However, it is impossible to protect the unit from direct contact with water. Therefore, ARCO maintain their products in the way that their customers grant satisfaction when it comes to quality. Like their outboard stator with part no.  3412. This starter will fit your Suzuki, Tohatsu and Nissan engines. Engine usually use for 30 and 40 HP. The part numbers that replace the Hitachi are S108-94, S108-112, S108-120. Use also with 9 tooth gear. If you have questions on shipping, feel free to email at sales@magemarinestore.com or contact us at 702-582-9667.

CMC PT-35 Owner’s Manual

Manual is used to understand the system and process of one unit or any equipment. If you are about to install or use equipment you can always use the manual as your help. Let say,  you are going to use your boat and you bought a new PT-35 Tilt Trim unit and you don’t know how to install it properly. It seems like you needed a manual with a very clear explanation. Now you can have the CMC PT-35 Owner’s Manual for your convenience. It’s only $12.52. Just click it here: http://magemarinestore.com/ptowma52.html and get the information you will need.

A switch box is often needed in a boat, car, stereo and any machines. The switch is used to control the motions of machines, interrupting the current of electrical component or diverting it from one conductor to another. CDI manufactured different switch box to fit for boat engine. MagemarineStore will help you find your switch box. One of the switch boxes we have is part no. 114-2803 to use for Mercury engine with 95 HP and 110 HP. Fits for year 1966-1967. The Switch box and ignition coil are attached to a mounting plate for easy installation. This unit is a replacement to the original case. It does not contain a rev limiter or tach circuit. You can replace your old mercury switch box with part numbers 332-2803A3 and 332-2803A4.  

ARCO BI-0702 Battery Isolator

Do you know that the most common battery isolator is the one alternator, two battery units? But it doesn’t matter how many batteries are connected in parallel to the battery 1 or 2 terminal. Remember, when batteries are connected in parallel, they become one large battery. With the use of one alternator, the two battery isolator with a battery selector switch will allow both banks of batteries to be charged regardless of what position the battery selector switch is in. The two alternators or two battery isolators allows both alternators to charge both batteries. In the event of one alternator failure, both batteries would be maintained by the working alternator.

One of these common battery isolators manufactured by ARCO is this part no. BI-0702. This isolator has one alternator and two batteries with a maximum 70 AMP electrical current.  Our cost is only $55.37. We offer discounts if you requested to ship USPS service, just let us know.  Visit this link now http://magemarinestore.com/arbais.html.

9” Static Setback 90012

You got a great deal of boat with 200 HP. However, it has a 20 inch lower unit.  And your question is, “would you be able to lower the motor with the 20” lower unit to sit while the 25” lower unit sat before?”

Well, if you don’t want to tilt your motor, you could purchase the 90012 with 9”setback plate. The unit would set the motor back from the transom 9” and taper down 5-3/4. You would be able to tilt your motor some, but not all the way. When you want to come down with a motor, you will have this problem unless you set your motor back 20-26”.

This CMC 90012 jack plate for your boat has 1 ½ inches of adjustment at the marine transom and 1” of adjustment on the motor bracket.  You can use this to give a total set back of 14.5” when used with the 65201 which has 5.5” set back. One of the CMC jack plates that are made of 6160 T6 extruded aluminium alloy. Rated for V-6 and smaller boat engine applications. Dimension from top of transom to top of motor side is 5 ¾ inches.  This jack plate provides better fuel efficiency.  It has stainless steel fasteners for maximum strength and durability.

To give you this part, you can follow this link and order online: http://magemarinestore.com/9instse.html  for $303.00 and will absolutely satisfy your boating performance.

Racks for Wakeboard Tower

Boats are designed to have accessories like wakeboard tower and wakeboard tower needs board racks to holds two wakeboards and skis. CMC manufactured wakeboard racks from polished aluminium for supreme weather resistance and covered with vinyl sleeves for ultimate board protection.  Racks fit most towers with round tubing. The round tubing outside diameter is from 1 ½ to 2 inch. But before you install it you must have horizontal bar already available on your existing tower. You can easily and quickly install it. Check our website MagemarineStore.com and visit our wakeboard racks with a regular price of $70 and now it's only $59.00. Hurry up!

CMC Universal Wake Board and Ski Rack 9750